Mes Notices

600 000 notices et 900 000 pièces détachées électroménager

Notice ZANUSSI NH90EPN

Télécharger la notice

Extrait du mode d'emploi ZANUSSI NH90EPN

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

d - Mark the centres for the keyhole bracket fixing screws. 4 - Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall brackets 1-2 using the rawl plugs and screws supplied. 5 - Splashback (optional) When a splashback is to be fitted, the distance between the cooker hood and the cooking ap-pliances will be determined by the height of the splashback, item B. The splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes care must be taken to ensure that the splashback is fitted at the correct height before fixing it into position. The fitting should be undertaken by a a com-petent person with experience in this type of installation. If the splashback is to be fixed through only the top fixing holes proceeds as follows: a - Put the splashback on the worktop as illu-strated in fig. 2a; then holding it against the wall to ensure that it is correctly positioned mark the holes for the top fixing screws on the wall. b - Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs and screws supplied. c - If the fixing holes in the bottom of the splashback are not to be used to secure the splashback to the wall the installer should ensure that the bottom edge is tucked down behind the rear of the worktop. 2 1 2 3 4 Fixing the canopy hood (fig. 3) Adjust the two screws V (on the canopy connection points) to approximately half way. Hook the rear of the canopy to the wall bracket 1, after anchoring the latter to the wall. Turn the screws V to adjust the canopy vertically and level it horizontally. Fit and lock the central fixing screw V1 (porvided) to lock the canopy in place. 3 - Electrical connection and working test 1 - The safety measures 3. 3 and 3. 4 of paragrapf 3 are to be strictly observed. [...] 2 - senza fondale; d = 937 mm almeno. - Verificare che la staffa 1 sia in posizione orizzontale. Piccoli aggiustamenti saranno possibili tramite le viti di regolazione della cappa (vedi oltre). b - Segnare sulla parete i centri dei due fori asolati della staffa. 3 - Posizionamento delle staffe 2 a - Appoggiare una delle staffe 2 sulla parete a circa 1 o 2 mm dal soffitto o dal limite superiore, allineando il suo centro (intagli) sulla linea verticale. b - Segnare sulla parete i due fori asolati della staffa. c - Appoggiare l'altra staffa 2 sulla parete, allineandola alla linea verticale, ad una distanza X misurata come in fig. 2, pari all'altezza del semitubo superiore S in dotazione alla cappa. La quota X può avere valori differenti, secondo le varie altezze disponibili del semitubo superiore. d - Segnare sulla parete i centri dei fori asolati della staffa. 4 - Con una punta Ø 8 mm forare tutti i centri segnati, quindi fissare a fondo le staffe 1 - 2 usando i tasselli Ø 8 mm e le relative viti in dotazione. 5 - Fondale (opzionale) L'altezza della cappa dal piano di cottura è determinata, in questo caso, dall'altezza del fondale B e dalla eventuale alzatina del piano delle basi. Il fondale va montato prima di montare il corpo cappa, e, se si desidera fissarlo contro la parete sia superiormente che inferiormente, è necessario montarlo alla giusta altezza, prima del montaggio delle basi o almeno del relativo piano superiore. Essendo questa operazione complessa va effettuata solamente dall'installatore della cucina o da personale competente che conosca tutte le dimensioni finali dei mobili. Limitandosi al solo fissaggio superiore procedere come segue: a - Appoggiare il fondale sul piano della basi come in fig. 2a, mandarlo a contatto della parete e centrarlo rispetto alla base. b - Segnare sulla parete i centri dei due fori della faldina superiore...

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre ZANUSSI NH90EPN : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Jeudi 9 Septembre 2008.

Vous pouvez télécharger les notices suivantes connexes à ce produit :

   ZANUSSI NH90EPN (5892 ko)

Liens commerciaux