Mes Notices

600 000 notices et 900 000 pièces détachées électroménager

  1. MesNotices
  2. Mode d'emploi
  3. Yamaha

Notice YAMAHA MAGICSTOMP GUITAR EFFECTS PROCESSOR MK2

Télécharger la notice

Extrait du mode d'emploi YAMAHA MAGICSTOMP GUITAR EFFECTS PROCESSOR MK2

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

U96«Natural 00CAN'T0DETECT w If the application of a single band filter does not take care of the feedback, press the switch as described in step q and set a second filter. A maximum of 5 band filters can be set. * The following display will appear if all 5 filters have been set. U96«Natural 0AFR0BAND0FULL! The AFR Function's settings are not saved along with patch data. And the AFR Function's settings are cancelled when another patch is selected. [STORE/EXIT Button] In the original MAGICSTOMP, the ON/OFF switch used in step r of the "Giving the Patch a Name" section on page 19 in the original MAGICSTOMP Owner's Manual, is now the [STORE/ EXIT] button (refer to the example below). r After you've changed the name, press the ON/OFF switch. The MAGICSTOMP is now in store standby mode. r After you've changed the name, press the [STORE/EXIT] button. The MAGICSTOMP is now in store standby mode. U01:TUBE0DRIVE1 PRESS[STORE]1sec Press Press U01:TUBE0DRIVE1 PRESS[STORE]1sec 5 English GUITAR EFFECTS PROCESSOR Nouveautés et améliorations du modèle MK2 [Édition complète] La fonction « Édition complète » du modèle MK2 vous permet de modifier n'importe quel paramètre d'un patch, de définir les paramètres commandés par les trois potentiomètres de l'appareil, et de mémoriser ces réglages. Sur le modèle d'origine du MAGICSTOMP, l'édition complète et l'affectation des paramètres aux potentiomètres n'étaient possibles que par l'intermédiaire d'un ordinateur utilisant l'application « Sound Editor for MAGICSTOMP ». Avec le MAGICSTOMP MK2, toutes ces opérations peuvent être effectuées directement sur l'appareil. Pour plus de précisions, reportez-vous à la page 7 de ce document. Français [Jack PHONES] La prise PHONES (mini-jack stéréo) vous permet de travailler ou de modifier des patches tout en écoutant le son émis par le MAGICSTOMP via un casque stéréophonique. (Niveau/impédance de sortie : ­10dBm/150) * Utilisez le potentiomètre de volume pour régler le volume. * La sortie sur les jacks OUTPUT n'est pas modifiée par le branchement d'un casque sur le jack PHONES. Jack PHONES Lors de l'écoute au casque, réglez soigneusement le niveau sonore pour ne pas blesser votre ouïe. [...] First, use the procedure described below to set the AFR Function ON (activate the function). q After pressing the [STORE/EXIT] button, press the ON/OFF switch two times to select the "Effect Type Select" display in the Deep Edit Mode. * When pressing the switch two times, make sure the switch is released within one second both times. ÿEDIT-FXT:63/63Y ØAcousticMulti w Until the following display appears, press and hold (for about four seconds) the ON/OFF switch. ÿEDIT-FXT:63/63Y AFR0FUNCTION0ON The display shown above will appear for one second and then return to the display that was selected before the [STORE/EXIT] button was pressed. * To switch the AFR Function OFF again, follow steps q and w described above once again. The procedure described above only has an effect on patches that have their effect type set to "AcousticMulti". Also, the AFR function's ON/OFF setting effects all patches, it can not be set in individual patches. s Using the AFR Function After you have switched ON (activated) the AFR function using the procedure described on the previous page, the "«" edit icon will appear for patches that can use the AFR function (patches that have their effect type set to "AcousticMulti"). U011«Natural óBASSfiMID0áTRE * The normal "¤" edit icon appears when the AFR function is set OFF (inactive), or when a patch is selected that uses an effect type other than "AcousticMulti". 4 After selecting a patch in which the AFR function is active, follow the instructions below to use the AFR function. * The AFR function's switch operation differs in the Up/Down Mode and Performance Mode. q When feedback occurs in the Up/Down Mode press the ON/OFF switch, and when in the Performance Mode press the switch that corresponds to the currently selected patch (­, ON/OFF, +). * The switches in the procedure described above (­, ON/OFF, +) can not be used to switch effects ON/OFF in patches that have the AFR function active. The MAGICSTOMP will automatically identify the frequency causing the feedback and activate an unused notch filter. When the filter identifies the problem frequency, the display will appear similar to that shown below and then return to its previous condition. To indicate that the AFR function is active, the ON/OFF switch's lamp will flash when in the Up/ Down Mode, while in the Performance mode, the switch's lamp (­, ON/OFF, +) for the currently selected patch will flash. [...]..

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre autres YAMAHA MAGICSTOMP GUITAR EFFECTS PROCESSOR MK2 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Mardi 4 Avril 2008.

Vous pouvez télécharger les notices suivantes connexes à ce produit :

   YAMAHA MAGICSTOMP GUITAR EFFECTS PROCESSOR MK2 (783 ko)
   YAMAHA MAGICSTOMP GUITAR EFFECTS PROCESSOR MK2 (778 ko)

Vos avis sur le YAMAHA MAGICSTOMP GUITAR EFFECTS PROCESSOR MK2

 Excellent matériel, je ne regrette pas mon achat. Pas de regret sur mon achat, trs bon effet.