Notice TOSHIBA RBC-SR1-PE

Notice

---

TOSHIBA RBC-SR1-PE

© copyright TOSHIBA

Télécharger la notice

Extrait du mode d'emploi TOSHIBA RBC-SR1-PE

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

OFF ON 88 °C 88 : 88 H 6 TIMER ADJUST CHECK FILTER ADDRESS M 5 ON/OFF 9 1. MODE Button Selects the desired operation mode. Each time it is pressed, the display changes in the following sequence:FAN ONLY ¨ COOL ¨ HEAT ¨ AUTO 2. FAN Button Selects the desired fan speed mode. Each time it is pressed, the display changes in the following sequence:AUTO ¨ HIGH ¨ MED ¨ LOW 3. LOUVER Button This is used to drive the outlet louvers automatically when the air conditioner is in operation. When it is pressed, the louvers will start oscillation and the display will illuminate. When it is pressed again, the louvers will stop. TEMP ADJUST ( w v ) Buttons These buttons are used to set the required room temperatures (18-29°C). TIMER Button 10 7 8 6. TIMER ADJUST Buttons 7. OPERATION Lamp On initial power on or after a power interruption this lamp will flash. This lamp is lit during normal operation. ON/OFF Button When this button is pressed, the machine starts or stops within a couple of minutes. CHECK Button 10. FILTER Button q CHECK button and FILTER button are for the use of service engineers. CAUTION q When the air conditioner is switched off, the operation lamp and LOUVER display go off, but the other displays remain unchanged. q Use the CHECK button for a malfunction check. Do not operate this button under normal ­5­ GB AI REMOTE CONTROLLER MANUAL OPERATION The Main Isolation Switch needs to be set to the "on" position (the operation lamp flashes). Caution q Do not turn the power OFF while the machine is in use. q If the air conditioner is to be used after a long period of mains power isolation, ensure the air conditioner has mains power supplied for 12 hours before operation. 1 2 NETWORK MODE FAN ONLY COOL FAN AUTO HIGH MED HEAT AUTO TEMP UNIT CHECK LOW CENTRAL OPERATION STANDBY PREHEAT DEFROST FILTER LOUVER MANUAL MODE REMOTE CONTROLLER 3 - + 88 °C TIMER CONT. OFF ON ADDRESS CHECK TIMER ADJUST 88 : 88 H M FILTER ON/OFF 4 1. MODE Button Selects the desired operation mode. Each time it is pressed the display changes in the following sequence:FAN ONLY ¨ COOL ¨ HEAT ¨ AUTO 2. [...] 30 AUTOMATISCHE WERKING. 31 VOORVERWARMEN. 32 KOELEN. 33 ­3­ GB AI REMOTE CONTROLLER REMOTE CONTROL DISPLAY All of the display items are shown in the diagram below for the purpose of explanation. Only selected items are displayed in actual operation. 234 5 6 7 NETWORK 1 9 11 10 12 13 MODE FAN ONLY COOL FAN AUTO HIGH MED CENTRAL OPERATION STANDBY PREHEAT DEFROST FILTER REMOTE CONTROLLER 8 MODE HEAT AUTO TEMP UNIT LOW CHECK LOUVER MANUAL - + TIMER CONT. OFF ON 88 °C 88 : 88 H TIMER ADJUST ADDRESS CHECK FILTER M ON/OFF 14 1. MODE Display Displays selected operation mode. FAN Display Displays selected fan speed mode. CENTRAL Display This is displayed if air conditioner operation is being restricted by the central remote controller. If "central" is flashing, the air conditioner is locked in the "off" position by the central remote controller. OPERATION Display This is displayed during the air conditioner operation. STANDBY Display This is displayed if the air conditioner is connected to a super multi system when operation is being disabled. PRE HEAT DEFROST Display This display appears at the start of the heating operation or during the defrost operation. FILTER Display This display appears after 2500 hrs of operation. LOUVER or LOUVER MANUAL Display "Louver" is displayed if the automatic louvers are driven. "Louver manual" is displayed if "auto louver" is selected but not available. CHECK Display This display appears when the air conditioner is in the "check" mode. UNIT Display This is used in the "check" mode. TEMP Display This display shows the set temperature. TIMER Display If the lapse timer is selected for "on" or "off". If the timer is reset to "continuous", this is displayed, then disappears. TIME OR CHECK Display This display shows the time remaining to "on/off" for the timer or the inspection code. ADDRESS Display When LAN addresses are set, this is displayed. [...]..

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre climatiseur TOSHIBA RBC-SR1-PE : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Vendredi 2 Février 2011.