Notices lave-vaisselle TEKA DW7 45 S, LP2 140, TEKA DW1 605 FI

Liens commerciaux

Les documents suivants correspondent à des notices, modes d'emploi ou brochures pour TEKA :

TEKA DW7 45 S (2973 ko)

TEKA LP2 140 (6730 ko)

TEKA DW1 605 FI (1154 ko)

Les modes d'emploi lave-vaisselle TEKA DW7 45 S (et TEKA LP2 140, DW1 605 FI) vous rendent service

Vous avez l'impression que votre lave vaisselle ne s'alimente plus en eau, une icône s'affiche sur son écran et représente un robinet, ce qui tend à confirmer votre hypothèse. Vous comprendrez comment ouvrir à fond le circuit d'alimentation en eau de votre lave vaisselle pour éviter qu'une erreur ne se déclenche en consultant la notice de votre TEKA DW7 45 S (et TEKA LP2 140, DW1 605 FI). Dans les minutes qui suivent sa mise en route, votre lave vaisselle émet un bip sonore, signe qu'une des pièces détachées électroménager est défectueuse, puis le répète à trois reprises, vous aimeriez savoir ce que cela signifie. Le lavage à 60°C se réalise habituellement en un cycle de 1H30, seulement la durée est actuellement majorée d'une grosse demi-heure. Le manuel de votre TEKA DW1 605 FI, et TEKA LP2 140, DW7 45 S, vous expliquera comment réduire le temps de réalisation du cycle à la valeur que vous désirez.

Ces notices de lave-vaisselle TEKA ont été ajoutées le Mercredi 11 Novembre 2019.

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre lave-vaisselle TEKA : mode d'emploi, notice d'utilisation, manuel d'instruction.

Extrait du mode d'emploi : notice TEKA DW7 45 S

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction; make sure that the hoses are not kinked, crushed or pulled too tightly. Make sure to tighten the locking ring-nut once the pipes have been placed in the direction required. A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass. Before putting the dishwasher into its definitive position, turn on the water tap and check that there are no leaks from the tap connection, the dishwasher connection or the hose. Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring correct operation of the dishwasher. [...] LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK. NEVER LEAVE THE DISHWASHER DOOR OPEN; PEOPLE MIGHT TRIP OVER IT. KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE TOP BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE BASKET. AQUASTOP MODELS THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED, CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT. IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE. DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER. [...]..

Extrait du mode d'emploi : notice TEKA DW1 605 FI

The covering fixtures are available as an accessory from specialist dealers or the After-Sales Service. - To build in the dishwasher, the special kit must be purchased from authorised dealers or the After-Sales Service. Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance. 31 Installation instructions 2. 1 Water supply connection Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance. The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused. [...] IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE. DO NOT ATTEMPT TO REPAIR THE APPLIANCE. THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN: REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER. [...]..