Notice ROLAND E-09W
Extrait du mode d'emploi ROLAND E-09W
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
1 - 16) vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63), Initial value = 40H (no change) ❍Effect 3 (Chorus Send Level) (Controller number 93) Status BnH 2nd byte 5DH 3rd byte vvH ❍Decay Time (Controller number 75) Status BnH 2nd byte 4BH 3rd byte vvH n = MIDI channel number: 0H - FH (ch. 1 - 16) vv = Chorus Send Level: 00H - 7FH (0 - 127), Initial value = 00H (0) * This message adjusts the Chorus Send Level of each Part. n = MIDI channel number: 0H - FH (ch. 1 - 16) vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63), Initial value = 40H (no change) ❍NRPN MSB/LSB (Controller number 99, 98) Status BnH BnH 2nd byte 63H 62H 3rd byte mmH llH ❍Vibrato Rate (Controller number 76) Status BnH 2nd byte 4CH 3rd byte vvH n = MIDI channel number: 0H - FH (ch. 1 - 16) vv = Vibrato Rate value (relative change): 00H - 40H - 7FH (-64 - 0 - +63), Initial value = 40H (no change) n = MIDI channel number: 0H - FH (ch. 1 - 16) mm = upper byte (MSB) of parameter number specified by NRPN ll = lower byte (LSB) of parameter number specified by NRPN * Rx. NRPN is set to OFF by power-on reset or by receiving “GM1 System On” or “GM2 System On,” and NRPN message will be ignored. NRPN message will be received when Rx. NRPN = ON, or by receiving GS RESET. The value set by NRPN will not be reset even if Program Change or Reset All Controllers is received. ❍Vibrato Depth (Controller number 77) Status BnH 2nd byte 4DH 3rd byte vvH * n = MIDI channel number: 0H - FH (ch. 1 - 16) vv = Vibrato Depth Value (relative change): 00H - 40H - 7FH (-64 - 0 - +63), Initial value = 40H (no change) **NRPN** The NRPN (Non Registered Parameter Number) message allows an extended range of control changes to be used. On the E-09, NRPN messages can be used to modify sound parameters, etc. To use these messages, you must first use NRPN messages (Controller number 98 and 99, their order does not matter) to specify the parameter to be controlled, and then use Data 2 Roland E-09 MIDI Implementation Entry messages (Controller number 6) to specify the value of the specified parameter. Once an NRPN parameter has been specified, all Data Entry messages received on that channel will modify the value of that parameter. To prevent accidents, it is recommended that you set RPN Null (RPN Number = 7FH 7FH) when you have finished setting the value of the desired parameter. [...] 1 - 16) vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON * Not received when Rx. SOFT = OFF. (Initial value is ON) n = MIDI channel number: 0H - FH (ch. 1 - 16) kk = source note number: 00H - 7FH (0 - 127) * * A Note-on received immediately after a Portamento Control message will change continuously in pitch, starting from the pitch of the Source Note Number. If a voice is already sounding for a note number identical to the Source Note Number, this voice will continue sounding (i. , legato) and will, when the next Note-on is received, smoothly change to the pitch of that Note-on. The rate of the pitch change caused by Portamento Control is determined by the Portamento Time value. ❍Filter Resonance (Timbre/Harmonic Intensity) (Controller number 71) Status BnH 2nd byte 47H 3rd byte vvH * n = MIDI channel number: 0H - FH (ch. 1 - 16) vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 - +63), Initial value = 40H (no change) ❍Release Time (Controller number 72) Status BnH 2nd byte 48H 3rd byte vvH Example 1. On MIDI 90 3C 40 B0 54 3C 90 40 40 80 3C 40 80 40 40 Example 2. On MIDI B0 54 3C 90 40 40 80 40 40 Description Note on C4 Portamento Control from C4 Note on E4 Note off C4 Note off E4 Result C4 on no change glide from C4 to E4 no change E4 off n = MIDI channel number: 0H - FH (ch. 1 - 16) vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63), Initial value = 40H (no change) ❍Attack time (Controller number 73) Status BnH 2nd byte 49H 3rd byte vvH Description Portamento Control from C4 Note on E4 Note off E4 Result no change E4 is played with a glide from C4 to E4 E4 off ❍Effect 1 (Reverb Send Level) (Controller number 91) Status BnH 2nd byte 5BH 3rd byte vvH n = MIDI channel number: 0H - FH (ch. 1 - 16) vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63), Initial value = 40H (no change) ❍Cutoff (Controller number 74) Status BnH 2nd byte 4AH 3rd byte vvH n = MIDI channel number: 0H - FH (ch. 1 - 16) vv = Reverb Send Level: 00H - 7FH (0 - 127), Initial value = 28H (40) * This message adjusts the Reverb Send Level of each Part. [...]..
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre ROLAND E-09W : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Samedi 3 Mars 2011.
Vous pouvez télécharger les notices suivantes connexes à ce produit :
