Notice RAZOR LIL

RAZOR

Notice

---

RAZOR LIL

© copyright RAZOR

Télécharger la notice

Extrait du mode d'emploi RAZOR LIL

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

Remove washer (A) from fork. Insert the front fork into the steering tube. Slide washer (A) back onto the front fork. Slide collar clamp (B) back down onto the fork until it is sitting directly on top of washer (A). C q Attaching the T-bar Tools Needed: 13 mm wrench C 1 Slide collar clamp cover (C) up to the middle of the T-bar. Insert the T-bar all the way down into the front fork. 2 Align the handlebars with the front wheel and using a 13 mm wrench, tighten the collar clamp bolt until the handlebars are locked securely into place. Slide the collar clamp cover down over the collar clamp. Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers at www. razor. com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the product I. code available for better assistance. 4 Lil’ KICK PARTS Keep your Lil’ Kick scooter working for years with genuine Razor parts. Visit our web site to purchase replacement parts. (Specifications subject to change without notice. ) 1 Handlebar Grips 2 Handlebar Pad 3 Handlebar 3-1 Bolt (x2) 3-2 3-3 Spring Washer (x2) Nut (x2) 5 Collar Clamp Cover 6 Collar Clamp 6-1 Bolt 6-2 6-3 Spring Washer Lock Nut 9 Front Wheel 9-1 9-2 9-3 9-4 Fixed Cap (x2) C Clip (x2) Front Axle Front Wheel Bushing / Spacer (x2) 11 Rear Wheel (x2) 11-1 Short Bushing / Spacer (x4) 12 Rear Axle Bolt 12-1 Rear Tube Cover (x2) 12-2 Washer (Large) (x2) 12-3 Washer (x2) 12-4 Spring Washer (x2) 12-5 Locknut (x2) 7 Washer 8 Plastic Headset (upper/lower) 4 T-bar 10 Front Fork 10-1 Fork Cover (x2) 1 2 3-1 3 1 3-2 3-3 4 5 6 6-1 7 8 6-3 6-2 11 11-1 11-1 12-5 12-4 12-3 12-2 12-1 9 9-1 9-2 9-3 9-2 9-1 10 10-1 11 11-1 11-1 9-4 11-2 12 12-3 12-4 12-5 5 Safety reminders PRE-RIDE CHECKLIST q Loose Parts Check and secure all fasteners before every ride. Make sure the T-bar and wheels are tight. There should not be any unusual rattles or sounds from loose parts or broken components. q Safety Gear q Frame, Fork and Handlebars Always wear proper protective equipment, such as an approved safety helmet, elbow pads and kneepads. Always wear close toe shoes (laceup shoes with rubber soles), never ride barefooted or in sandals and keep shoelaces tied and out of the way of the wheels. [...] The original equipment supplied at the time of sale was selected on the basis of its compatibility with the frame, fork and all other parts. Certain aftermarket products may not be compatible. Use of any nonRazor product parts will void your warranty. q Estimated Assembly and Set-Up Time Adult assembly required. Allow up to 10–15 minutes for assembly. Handlebar Pad Handlebar Grips T-bar Collar Clamp and Cover PRODUCT I. CODE Front Fork 1. Underneath the deck 2. UPC Side of Box (not shown) Front Wheel Deck Barcode Location Rear Wheels q Required Tools Two (2)10 mm and 13 mm wrenches (Included) Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers at www. razor. com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the product I. code available for better assistance. 2 Set-Up and usage q Assembling the Handlebars Tools Needed: 10 mm wrench Note: For further assistance, please refer to page 5 for parts breakdown. 1 Align the holes on the handlebars and the T-bar. Insert handlebar bolts into the top of the handlebar and through the T-bar. Install the washers and nuts onto the bottom of the handlebar bolts. Tighten securely into place using a 10 mm wrench. 2 Place the handlebar pad over the handlebars and secure tightly with the velcro cover. q Assembling the Rear Wheels Tools Needed: Two (2) 10 mm wrenches 3-3 3-1 3-2 Rear wheel hardware sequence 3-1 - Locknut 3-2 - Spring washer 3-3 - Washer (small) 3-4 - Axle bolt Wheel 3-5 - Washer (large) 3-5 3-5 3-2 3-4 3-1 3-3 Frame 1 Remove the locknut, spring washer and washers (x3) from one side of the axle bolt. Insert the axle bolt through the rear wheel. Insert the large washer (3-5) onto the axle bolt between the frame and rear wheel and slide the axle bolt through the frame. Slide the other large washer and wheel onto the axle bolt. Note: Wheels are interchangeable. 2 Insert the small washer (3-3), spring washer (3-2) and locknut (3-1) onto the axle bolt and tighten securely using two (2) 10 mm wrenches. 3 Make sure the locknut, spring washer and small washer are securely tightened against the wheel. 3 SET-UP and USAGE q Assembling the Front Fork Tools Needed: 13 mm wrench B A A B 1 Remove the black protective cover from the top of the fork. [...]..

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre trottinette électrique RAZOR LIL : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Lundi 1 Janvier 2020.

Envoyer vos modes d'emploi - Foire aux questions - Dernières recherches - Derniers ajouts - Sitemap - Contactez-nous - Conditions générales - Politique de cookies

Copyright - Tous droits réservés.
Les noms de marques cités appartiennent à leurs propriétaires respectifs.