Notice RAZOR E300

RAZOR

Notice

---

RAZOR E300

© copyright RAZOR

Télécharger la notice

Extrait du mode d'emploi RAZOR E300

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

WARNING: Keep your fingers clear of the pivoting mechanism when folding or unfolding the scooter, and make sure others are standing clear. Note: The cable and wire assembly from the handlebar must not wrap around the steering tube or handlebar as shown in step 3. Sharp bends or twisting of the brake cable can cause the brakes to malfunction. 1 Loosen the locking knob and swing to the 6 o’clock position to unfold the handlebar. 2 Remove the plastic protector covering the base of the handlebar assembly. Insert the “quill” part of the handlebar assembly into the fork. You may have to loosen the wedge to allow it to slip into the fork. 3 Slide the quill into the fork until it bottoms on the headset. 4 Using a 6mm hexagonal key wrench, tighten the wedge by turning the bolt clockwise. The wedge is properly tightened when the handlebars cannot be twisted out of alignment with the front wheel. q Inflating the Tires Rear Tire 5 Pivot the handlebar assembly upright. 6 Swing the locking knob to the 12 o’clock position and tighten by hand as firmly as possible. Tires are inflated when shipped, but they invariably lose some pressure between the point of manufacturing and your purchase. Always inflate tires to the correct PSI before first time use. WARNING: Failure to remove the valve adapter after inflating will cause the inner tube and/or adapter to be severed by the rear drive sprocket. Note: If you lose the valve extender, one can be purchased at almost any auto parts store. Note: The pressurized air supplies found at gasoline stations are designed to inflate high-volume automobile tires. If you decide to use such an air supply to inflate your electric scooter tires, first make sure the pressure gauge is working, then use very short bursts to inflate to the correct PSI. If you inadvertently over-inflate the tire, release the excess pressure immediately. 1 Use the valve extender located inside the end of the right handlebar grip. 2 Open the round cover located on the chain cover by sliding the cover upward. Align the opening in the drive sprocket with the valve stem. Thread the adapter completely onto the valve stem and attach the pump. Inflate to the PSI indicated on the tire sidewall. 3 3 Remove valve extender immediately after inflating and close the round cover. [...] Do not exceed charging time. Always disconnect from the charger prior to wiping down and cleaning your scooter with liquid. FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION. 1 Before You Begin Remove contents from box. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the scooter is 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. WARNING: DO NOT USE NONRAZOR PRODUCTS WITH YOUR RAZOR ELECTRIC SCOOTER. The scooter has been built to certain Razor design specifications. The original equipment supplied at the time of sale was selected on the basis of its compatibility with the frame, fork and all other parts. Certain aftermarket products may or may not be compatible. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES. Estimated Assembly and Set-Up Time Charger Allow up to 20 minutes for assembly, not including initial charge time. Allow up to 18 hours for initial charge (see page 3 for charging information) Brake Lever Charger Port Charger Plug Valve Extender (inside grip) Twist Grip Throttle Seat (if applicable) Handlebar Stem -On/Off Switch -Charger Port -Reset Button Folding Mechanism Limiter Front Fork -Battery -Motor -Control Module Required Tools 6mm key wrench 8mm/10mm/17mm (Included) wrenches 4mm key wrench (Not Included) (Included) (300S ONLY) 2. 5mm/5mm key wrenches (Not Included) Phillips screw driver (Included) (300S ONLY) Valve extender (Located in right handlebar grip) Bicycle-style tire pump for Schrader valve tires, with pressure gauge (Not Included) Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers at www. razor. com or call toll-free at 866-467-2967 Monday - Friday 8:00AM - 5:00PM Pacific Time. 2 Assembly and Set-Up q Attaching the Handlebars Note: Make sure the cables/ wires are out of the way before inserting the stem in the fork. WARNING: Failure to properly tighten the wedge may allow the handlebars to dislodge while riding and may cause you to lose control and fall. [...]..

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre trottinette électrique RAZOR E300 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Lundi 1 Janvier 2020.

Envoyer vos modes d'emploi - Foire aux questions - Dernières recherches - Derniers ajouts - Sitemap - Contactez-nous - Conditions générales - Politique de cookies

Copyright - Tous droits réservés.
Les noms de marques cités appartiennent à leurs propriétaires respectifs.