Notice RAZOR E100, RAZOR POWERCORE E100S

RAZOR

Notice

---

RAZOR E100

© copyright RAZOR

Télécharger la notice

Extrait du mode d'emploi RAZOR E100

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

razor. com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. 2 Assembly and Set-Up q Attaching the Handlebars Note: Make sure the cables/ wires are out of the way before inserting the stem into the fork. (a) 1 Open the quick release. 2 Depress the push button (a) located on the front fork and insert the handlebar stem until the button locks securely into the fork. 3 Adjust the tension of the quick release to where you can close the lever all the way to secure the stem. Note: The pressurized air supplies found at gasoline stations are designed to inflate high-volume automobile tires. If you decide to use such an air supply to inflate the tire, first make sure the pressure gauge is working, then use very short bursts to inflate to the correct PSI. If you inadvertently over-inflate the tire, release the excess pressure immediately. WARNING: Always disconnect your scooter from the charger before cleaning with liquid. Note: If your charger does not look like the one illustrated, your unit has been supplied with an alternative charger. The specifications and charging procedure would not change. The charger has a small window with one LED or two LEDs to indicate the charge status. Refer to the illustration on the charger unit for the actual “charging” and “charged” status indications for your model charger. Chargers have built-in overcharge protection to prevent battery from being over-charged. q Inflating the Tire The front tire is inflated when shipped, but it invariably may lose some pressure between the point of manufacturing and your purchase. 1 Using a bicycle style tire pump equipped for a Schradertype valve, inflate the front tire to the correct PSI indicated on the sidewall of the tire. Your electric scooter may not have a fully charged battery. Therefore it is a good idea to charge the battery prior to use. • Initial charge time: 18 hours • Recharge time: up to 12 hours When the scooter is not in regular use, recharge the battery at least once a month until normal use is resumed. • Run time: Up to 40 minutes of continuous ride time • Average battery life: 250 charge/discharge cycles q Charging the Battery Charger Charger Port Charger Plug 1 Turn power OFF before charging. Plug the charger into the charger port on the electric scooter. 2 Plug the charger into a wall outlet. [...] Use only with the recommended charger. Use caution when charging. The charger is not a toy. Charger should be operated by an adult. Do not operate charger near flammable materials. Unplug charger and disconnect from scooter when not in use. Do not exceed charging time. Always disconnect from the charger prior to wiping down and cleaning your scooter with liquid. FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION. 1 Before You Begin Remove contents from box. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. WARNING: DO NOT USE NONRAZOR PRODUCTS WITH YOUR RAZOR ELECTRIC SCOOTER. The scooter has been built to certain Razor design specifications. The original equipment supplied at the time of sale was selected on the basis of its compatibility with the frame, fork and all other parts. Certain aftermarket products may not be compatible and will void the warranty. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES. Estimated Assembly and Set-Up Time Razor recommends assembly by an adult with experience in bicycle mechanics. Allow up to 20 minutes for assembly, not including initial charge time. Allow up to 18 hours for initial charge (see page 3 for charging information) Charger (Note: Charger design may vary from one shown) Brake Lever Charger Port Charger Plug Twist Grip Throttle Handlebar Stem Push Button Note: Electric scooter must be moving at 3mph/4. 8km before twisting the throttle to engage motor. Quick Release On/off switch Reset button Charger port Limiter Motor - Battery - Control Module Required Tools 2. [...]..

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre trottinette électrique RAZOR E100 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Lundi 1 Janvier 2020.

Envoyer vos modes d'emploi - Foire aux questions - Dernières recherches - Derniers ajouts - Sitemap - Contactez-nous - Conditions générales - Politique de cookies

Copyright - Tous droits réservés.
Les noms de marques cités appartiennent à leurs propriétaires respectifs.