Notice PHILIPS SCD480
Extrait du mode d'emploi PHILIPS SCD480
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
When the microphone sensitivity is set to `high', the baby unit picks up all sounds. Note:The sensitivity of the baby unit can only be changed when there is a connection between the baby unit and the parent unit. 1 Use the microphone sensitivity control to set the microphone sensitivity of the baby unit to the desired level. You can use your own voice as a sound reference (Fig. The power-on light on the baby unit turns yellow when a sound is transmitted. Note:Whilst operating on batteries, if the sensitivity is set to a high level, the parent unit will consume more power. adjustable loudspeaker volume You can change the volume on the parent unit, so you can adjust to suit your surroundings. 1 Turn the volume dial on the right side of the parent unit until the desired loudspeaker volume for the parent unit has been reached. Note:Whilst operating on batteries, if the volume is set to a high level, the parent unit will consume more power. Channel selector Always make sure that the channel selectors inside the battery compartments of both units are set to the same channel. With these channel selectors, you can select sixteen different channel positions. If you experience interference from other baby monitors, radio devices etc. , select a different channel. 1 Open the battery compartment lids of both units. 10 , , - EngliSh Baby unit: (Fig. ) Turn the locking knob with a coin and remove the lid. Remove the batteries from the battery compartment, if present. Use a small, flat screwdriver to turn the channel selector to the desired position. Parent unit: (Fig. ) Turn the locking knob a quarter turn (1) and slide the battery cover downwards to remove it (2). Remove the batteries from the battery compartment, if present. Use a small, flat screwdriver to turn the channel selector to the desired position. Note: Make sure both units are set to the same channel. If you do not experience any interference when you test the connection, close the battery compartments of the baby and the parent units. If you experience interference, set the selector to another channel and test the connection again. If the units are operating on non-rechargeable batteries, replace the batteries and close the battery compartments. [...] Note:When the batteries are completely empty, the parent unit automatically switches off and loses contact with the baby unit. using the appliance 1 Place the two units in the same room to test the connection (Fig. Make sure the baby unit is at least 1 metre/3 feet away from the parent unit. Press the on/off button to switch on the baby unit (Fig. The power-on light lights up green continuously. Turn the volume control to switch on the parent unit and to set the volume to the level you prefer. 7) The power-on light lights up green continuously. , When a connection has been established between the units, the connection light on the parent unit lights up green constantly. Note: It takes about 30 seconds before a connection is established. Note: If a connection cannot be established, the connection light on the parent unit flashes red. Place the baby unit at least 1 metre/ feet away from your baby (Fig. 5 Place the parent unit within the operating range of the baby unit. Make sure it is at least 1 metre/ feet away from the baby unit. For more information on the operating range, see section `Operating range' below (Fig. operating range The operating range of the baby monitor is 200 metres/600 feet in open air. Depending on the surroundings and other disturbing factors, this range may be smaller. Dry materials Material thickness Loss of range 0-10% 5-35% Wood, plaster, plaster cardboard, glass <30cm/12in (without metal, wires or lead) Brick, plywood <30cm/12in EngliSh Dry materials Reinforced concrete Metal grilles or bars Metal or aluminium sheets Material thickness <30cm/12in <1cm/0. 4in <1cm/0. 4in Loss of range 30-100% 90-100% 100% 9 For wet and moist materials, the range loss may be up to 100%. Features Digital signal confirmation The parent unit has a link light that continuously advises you of the status of the connection between the baby and the parent units. You can set an alert on the parent unit to notify you if the link is lost. The alert will sound an audible beep and the link light will flash red when a connection is lost. to activate the alert on the parent unit: 1 Turn the locking knob a quarter turn (1) and slide the battery cover downwards to remove it () (Fig. Set the link alarm switch in the battery compartment to the `on' position. Replace the battery compartment lid. To switch off the alert, set the link alert switch to the `off ' position. [...]..
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre PHILIPS SCD480 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Vendredi 2 Février 2009.
Vos avis sur le PHILIPS SCD480
Bon produit, très bon produit. Pour le prix j'ai mis 10 c'est un cadeau, bon dans l ensemble, très bien. Très bon modèle.
