Extrait du mode d'emploi : notice PHILIPS RQ1050
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
Press the on/off button once to switch off the shaver. , The display lights up for a few seconds and then shows the remaining battery capacity (RQ1090/ RQ1062/RQ1060 only). English 15
trimming You can use the trimmer to groom your sideburns and moustache. 1 Pull the shaving unit off the shaver. 2 Press the on/off button once to switch on the shaver. , The display lights up for a few seconds. Press the trimmer slide forwards to slide out the trimmer. 4 You can now start trimming. 5 Press the trimmer slide backwards to retract the trimmer. 6 Press the on/off button once to switch off the shaver. , The display lights up for a few seconds and then shows the remaining battery capacity (RQ1090/ RQ1060 only). 7 Insert the lug of the shaving unit into the slot in the top of the shaver (1). Then press the shaving unit downwards (2) to attach it to the shaver (`click'). Cleaning and maintenance Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. - Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. - Clean the shaver after every shave for optimal shaving performance. 16
- You can clean the outside of the shaver with a damp cloth. - Regular cleaning guarantees better shaving performance. Cleaning the shaving unit under the tap 1 Switch off the shaver. 2 Pull open the three shaving heads one by one. Rinse all three shaving heads and all three hair chambers under a hot tap for 0 seconds. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. 4 Carefully shake off excess water and leave the shaving heads open to let the shaving unit dry completely. Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads. , For thorough cleaning, switch on the shaver and immerse the shaving unit in hot water with some liquid soap for 0 seconds. You can also clean the shaving unit with some alcohol. English 17
Cleaning the shaving unit with the brush supplied 1 Switch off the shaver. 2 Pull open the three shaving heads one by one. Clean the shaving heads and the hair chambers with the brush supplied. 4 Close the shaving heads. Cleaning the trimmer with the brush supplied Clean the trimmer every time you have used it. 1 Switch off the shaver. [...] The travel lock prevents the shaver from being switched on by accident. activating the travel lock 1 Press the on/off button for seconds to enter the travel lock mode. , The lock symbol appears on the display (all types) and you hear a beep (RQ1090 only) to indicate that the travel lock has been activated. Note:The displays of types RQ1062, RQ1060, RQ1052, and RQ1050 look different but show the same indication. deactivating the travel lock 1 Press the on/off button for seconds. , The motor starts running to indicate that the travel lock has been deactivated. The shaver is now ready for use again. Note:When you place the shaver in the plugged-in Power Pod, the travel lock is automatically deactivated. English 1
Blocked shaving heads - If the shaving heads are blocked, the shaving unit symbol and the tap symbol with exclamation mark flash. In this case, the motor cannot run because the shaving heads are soiled or damaged. Note:The displays of types RQ1062, RQ1060, RQ1052, and RQ1050 look different but show the same indication. - When this happens, you have to clean the shaving unit or replace it. - The shaving unit symbol and the tap symbol with exclamation mark continue to flash until you unblock the shaving heads. Charging Charging takes approx. 1 hour. A fully charged shaver has a shaving time of up to 65 minutes, which is enough for approx. 21 shaves. The actual shaving time is calculated by the shaver. If you have a heavy beard, the shaving time may be less than 65 minutes. The shaving time may also vary over time, depending on your shaving behaviour and beard type. Quick charge After the shaver has charged for 5 minutes, it contains enough energy for one shave. 1 Put the small plug in the Power Pod. 2 Put the adapter in the wall socket. 14
Pull at the top of the lid (1) and remove it (2). 4 First insert the top of the shaver into the Power Pod (1) and then press the bottom part into the Power Pod (2). Note:The shaver cannot be placed in the Power Pod when the protection cap is on the shaving unit. , The display shows that the shaver is charging (see chapter `The display'). using the shaver shaving 1 Press the on/off button once to switch on the shaver. , The display lights up for a few seconds. 2 Move the shaving heads over your skin. Make both straight and circular movements. - Shaving on a dry face gives the best results. [...]..
Vos avis sur le PHILIPS RQ1050