Notice PHILIPS QC5135
Extrait du mode d'emploi PHILIPS QC5135
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
-- Write down the length settings you have used to create a certain hairstyle as a reminder for future clipping sessions. -- To clip in the most effective way, move the appliance against the direction of hair growth. -- Since hair grows in different directions, you need to move the appliance in different directions as well (upward, downward or across) (Fig. 7). -- Make overlapping passes over the head to ensure that the appliance catches all the hairs that need to be cut. Trimming with beard trimming comb Note: Make sure your facial hair is clean and dry. 1 Comb your beard or moustache with a fine comb before you start trimming. upwards with your thumb until it opens and then pull it off the appliance (Fig. 19). slot and push the cutting unit onto the appliance (‘click’) (Fig. 20). the guiding grooves of the appliance (‘click’) (Fig. 11). Make sure that the arms of the comb have been properly slid into the grooves on both sides. 3 Press the length setting selector (1) and then 2 Slide the beard trimming comb into 2 Place the lug of the new cutting unit in the move the beard trimming comb up or down (2) to set the desired length setting (Fig. 12). press the length setting selector (1), move the comb upwards and then pull it off the appliance (2). (Fig. 14) appliance through the hair slowly (Fig. 15). 2 Place the trimmer on the face and move the Length settings With the beard trimming comb attached, the appliance can cut hair to 8 different lengths: Environment -- Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 21). -- The built-in rechargeable batteries contain substances that may pollute the environment. Always remove the batteries before you discard and hand in the appliance at an official collection point. Dispose of the batteries at an official collection point for batteries. If you have trouble removing the batteries, you can also take the appliance to a Philips service centre. The staff of this centre will remove the batteries for you and will dispose of them in an environmentally safe way (Fig. [...] (Fig. 8) unit upwards with your thumb until it opens (Fig. 16). supplied (Fig. 17). and move the appliance through the hair slowly (Fig. 13). 3 Push the middle part of the cutting 2 Comb the hair ends over the ears before you 3 Slide the on/off slide upwards to switch on 4 Tilt the appliance in such a way that only one edge of the cutting element touches the hair ends. (Fig. 9) close to the ear. 5 Only cut the hair ends. The hairline has to be 6 To contour the neckline and the sideburns, 4 Slide the on/off slide upwards to switch on the appliance (Fig. 6). turn the appliance and make downward strokes (Fig. 10). smoothly. Follow the natural hairline. 5 Place the hair clipping comb on the scalp and 7 Move the appliance slowly and move the appliance through the hair slowly. Tips -- When you trim your beard for the first time, start at a length setting that is higher than the length of your beard hairs and reduce the length setting gradually. -- To trim in the most effective way, move the appliance against the direction of hair growth. -- Make overlapping passes over the chin to ensure that the appliance catches all the hairs that need to be cut. -- Make sure that the flat part of the beard trimming comb is fully in contact with the face to obtain an even trimming result. -- Regularly remove cut hair from the beard trimming comb. If a lot of hair has accumulated in the comb, remove it from the appliance and blow and/or shake the hair out of it. Creating a stubble beard -- To create a stubble beard, trim with the beard trimming comb set to 1. 5mm (1/16in). Clipping without beard trimming comb To trim your facial hair even shorter than 1. 5mm (1/16in), use the appliance without beard trimming comb. This results in a stubble beard of 1mm (1/32 in). 1 To remove the beard trimming comb, 4 Clean the cutting unit with the cleaning brush 5 Clean the inside of the appliance with the cleaning brush supplied (Fig. 18). 6 Clean the hair clipping comb and the beard trimming comb with the cleaning brush supplied. Note:The appliance does not need any lubrication. Replacement The cutting unit, the adapter and the hair clipping comb are replaceable. Replacing the cutting unit Replace the cutting unit if it is damaged or worn. Only replace the cutting unit with an original Philips cutting unit. [...]..
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre rasoir PHILIPS QC5135 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Lundi 3 Mars 2013.
