Notice PHILIPS PT730
Extrait du mode d'emploi PHILIPS PT730
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
2 Push the trimmer slide downwards to open the trimmer. 3 Clean the trimmer with the short-bristled side of the cleaning brush. Brush up and down along the trimmer teeth. 4 Close the trimmer (` click'). Tip: For optimal trimming performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months. English 15 storage - Put the protection cap on the shaver every time you have used it, to prevent damage. replacement For maximum shaving performance, we advise you to replace the shaving heads every year. Replace damaged shaving heads right away. Only replace the shaving heads with original HQ8 Philips Shaving Heads. 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 3 Pull the shaving unit off the shaver. 4 Turn the lock anticlockwise (1) and remove the retaining frame (2). 5 Remove the shaving heads and place new ones in the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 6 Put the retaining frame back into the shaving unit and turn the lock clockwise. 16 English 7 Insert the lug of the shaving unit into the slot in the top of the shaver (1). Then close the shaving unit (2). Note: If the shaving unit does not close smoothly, check if you have inserted the shaving heads properly and if the retaining frame is locked. accessories To retain the top performance of your shaver, make sure you clean it regularly and replace its shaving heads at the recommended time. shaving heads - We advise you to replace your shaving heads every year. Always replace with HQ8 shaving heads. Cleaning - Use Cleaning spray (HQ110) to clean the shaving heads thoroughly. Environment - Do not throw away the appliance with the normal household waste at the end of their life, but hand them in at an official collection point for recycling. By doing this, you help to preserve the environment. - The built-in rechargeable shaver battery contains substances that may pollute the environment. Always remove the battery before you discard or hand in the shaver at an official collection point. Dispose of the battery at an official collection point for batteries. If you have trouble removing English 17 the battery, you can visit our website, www. philips. com/support or call toll free: 1-866800-9311. removing the rechargeable shaver battery Only remove the rechargeable battery when you discard the shaver. [...] Always check if the water is not too hot, to prevent your hands from getting burnt. Note:Water may leak from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver. Cleaning the shaving unit under the tap 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 3 Rinse the shaving unit and hair chamber under a hot tap for 30 seconds. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. 12 English - Rinse the hair chamber and the inside of the shaving unit. - Rinse the outside of the shaving unit. 4 Close the shaving unit and shake off excess water. Be careful not to hit the shaving unit against anything while shaking off excess water. Never dry the shaving unit and the hair chamber with a towel or tissue, as this may damage the shaving heads and the coupling spindles. 5 Open the shaving unit again and leave it open to let the shaver dry completely. Cleaning the shaving unit with the cleaning brush 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 3 Pull the shaving unit off the shaver. English 13 4 Turn the lock anticlockwise (1) and remove the retaining frame (2). 5 Remove and clean one shaving head at a time. Each shaving head consists of a cutter and a guard. Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. - Remove the cutter from the shaving guard and clean it with the brush. - Clean the inside and outside of the shaving guard with the brush. 6 Put the shaving heads back into the shaving unit. 14 English PT860/PT735/PT730: Make sure that the projections of the shaving heads fit exactly into the recesses. 7 Put the retaining frame back into the shaving unit and turn the lock clockwise. 8 Insert the lug of the shaving unit into the slot in the top of the shaver (1). Then close the shaving unit (2). Note: If the shaving unit does not close smoothly, check if you have inserted the shaving heads properly and if the retaining frame is locked. Cleaning the trimmer with the cleaning brush (PT860 only) Clean the trimmer every time you have used it. [...]..
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre PHILIPS PT730 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Jeudi 11 Novembre 2011.
Vous pouvez télécharger les notices suivantes connexes à ce produit :
