Notice four LG SOLARDOM MODE D'EMPLOI et pièces détachées

Extrait du mode d'emploi : notice LG SOLARDOM MODE D'EMPLOI

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

Place the spring washer between the Flat washer and Nut. Mounting by using clamps • The module may be fastened to a support by using clamps on both the long edge and the short edge of the modules. • Specific information on the solar module dimensions and location of clamping is provided in ‘Product Specifications’. Solar module Supporting part Roof 6 Mechanical Installation LGXXXN1C(W)-G3 Mounting Type Use four mounting holes on two opposite sides. Clamping Type (Long Side) Clamping Range (230mm) 270mm 270mm Use four clamps on the long frame. This method is not tested by IEC/UL. Clamping Type (Short Side) Center ± 100mm Clamping Range: From module Edge to 270mm Center ± 100mm Clamping Range: From module Edge to 120mm Use four clamps on the short frame and two clamps at the center of long Frame. Use four clamps on the Short frame. This installation is allowed in the following cases: 1. Slope roof: If module is installed parallel to the rooftop. Flat roof: If installed with an additional stand such as wind shield or deflector. 7 Product Specifications - Electrical and Mechanical Properties (Rated electrical characteristics are within 10 percent) Standard Test Condition(STC) : Irradiation 1,000W/m2, Cell temp. 25°C, 1. 5AM Certificates Electrical Properties Mechanical Properties IEC61215 Ed. 2, IEC 61730, 5 Safety Class II, CE, ISO9001 Power To olerance Module Series S Vmpp at STC Pmax at STC Model Na ame Impp at STC S Voc at ST TC Max. of modules in series *Efficiency Reduction Connector Isc at ST TC LG250S1C(W)-A3 LG255S1C(W)-A3 LG260S1C(W)-A3 LGXXXS1X-A3 LG265S1C(W)-A3 LG270S1C(W)-A3 LG250S1K-A3 LG255S1K-A3 LG260S1K-A3 LG265S1K-A3 Yes Yes Yes Yes Yes Yes Yes Yes Yes W 250 255 260 265 270 % 3% 3% 3% 3% 3% 3% 3% 3% 3% V 37. 4 A 8. 17 V 30. 5 A 8. [...] • Do not touch the solar module with bare hands. Failure to comply may result in a serious burn or injury. • Do not drop the solar module or place weight on a solar module. • Do not disassemble the solar module. • After installation or repair, check that the solar module are operating properly. • In the event that the currently used solar module or parts have been replaced the newly replaced module and parts must have the same model name and parts as the previously installed solar module. • Secure all necessary permits and licenses to install the solar modules • Only qualified and authorized individuals are permitted to treat electrical parts, when there is a breakage, failure or damage of the product or damage of the product. • Do not use or install broken modules; Failure to comply may result in fire, electric shock, and injury. • Do not install the module horizontally. Failure to comply may result in excess dirt or white efflorescence (glass disease). • Panels are not intended for use indoors or on moving vehicles of any kind. • Reflection from external environments such as snow Reflection from external environments such as snow, water or other surfaces may increase the power generated by the panel. • Industry standard rated specifications are made at conditions of 1000W/m 2 irradiance and 25 °C (77ºF) solar cell temperature. Colder temperatures may substantially increase voltage and power. • Keep the solar module and system away from children at all times. • Keep the module packed in the carton until the time of installation. • Keep flammable gasses away from the installation site. • Do not work alone. Please work as part of a team of two or more people. • Safety harness use is strongly recommended for installation. • Partial shadowing may substantially reduce panel and system output...