Notice HUBSAN NANO Q4 (H001)

HUBSAN

Notice

---

HUBSAN NANO Q4 (H001)

© copyright HUBSAN

Télécharger la notice

Extrait du mode d'emploi HUBSAN NANO Q4 (H001)

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including including interference that may cause undesired operation 1. Transmitter and Quadcopter can not pair 8. 2 Backward Flip Push the Elevator stick backward quickly. Release the stick to the center after flip. 5 3 H001-01 4 H001-02 Screw H001-03 Propeller A H001-04 Propeller B Body Shell Set 1）Battery voltage is too low； 2）Re-bind； 3）Land the quadcopter on the ground with the throttle stick fully down, take off again after 3 seconds. Gyro not Working Well 4 5 6 Li-Po power is too low, re-charge the battery. Unable to Flip Mode 2 Mode 1 Mode 2 Mode 1 7 8 8. ADVANCED PERFORMANCE SETUP The default setting is Normal Mode, and the Expert Mode can be activated to have a better sensitivity on the performance of the quadcopter. Press the Elevator stick for 0. 5 second to shift between Normal Mode and Expert Mode, indicated by “Beeps”. Normal Mode/ Expert Mode 8. 3 Left Flip Push the Aileron stick to the left quickly. Release the stick to the center after flip. Check if motors, bodyshells and propellers are all properlly positioned or not; Check if motors and propellers damaged or not. [...] （2） Mode 1 Elevator/ Rudder Stick The Elevator stick moves the X4 forward and backward. Push the stick up the and the X4 will fly forward. Pull the stick down and the X4 will fly backward. The angle of stick movement corresponds to the angle of tilt and flight speed. Remote Controller 4 USB Charger 1pc For recharging the Li-Po Battery The battery should only be charged with the HUBSAN charger to avoid overcharge. 5 Manual 1PC Quick Guide Instruction 5 LED Indicator （2）Elevator/ Rudder Stick 4 Aileron Trim (1) Throttle/ Aileron Stick 3 4 5 3 Elevator Trim 6 Mode 1 Elevator Trim Aileron Trim LED Indicator Power Switch Important 1. 4 Prevent Moisture The quadcopter contains many precision electrical componets. Store the battery and the quadcopter in a dry area at room temperature. Exposure to water or moisture may cause malfunction resulting in loss of control. THE HUBSAN NANO Q4 SE ITEM NO: H001 ● Risk of explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the local regulations. Left The Aileron stick controls left and right flight. Push the stick to the left and the X4 will fly to the left. Push the stick to the right and the X4 will fly to the right. The angle of stick movement corresponds to the angle of tilt and flight speed. 5 Proper Operation For safety, pnly use Hubsan spare parts for replacement. ● Do not mix old and new batteries ● Do not charge non-rechargeable battery. 3 Headless Mode Headless Mode means the quadcopter default any directions (corresponding to the directions of transmitter sticks) asits up head when the mode is activated. 2 front LED blink simultaneously when in Headless Mode. Short press the Throttle stick for to enter/exit headless mode. Short press the Throttle stick to enter into the headless mode, indicated by two“Beeps”. Short press the Throttle stick again to exit the headless mode, indicated by one“Beep”. Mode 2 Mode 1 3. Exploded View 1 2 2 H001 SPARE PART LIST H001 TROUBLESHOOTING Throttle position needs to be fully down. Please do not move any sticks or trims during initial power-on binding. FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [...]..

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre drone HUBSAN NANO Q4 (H001) : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Lundi 9 Septembre 2020.

Envoyer vos modes d'emploi - Foire aux questions - Dernières recherches - Derniers ajouts - Sitemap - Contactez-nous - Conditions générales - Politique de cookies

Copyright - Tous droits réservés.
Les noms de marques cités appartiennent à leurs propriétaires respectifs.