Notice DJI MATRICE 100
Liens commerciaux
Le mode d'emploi DJI MATRICE 100 vous rend service
Vous ignorez pourquoi, après un an sans utilisation, votre drone qui fonctionnait très bien ne parvient plus à se calibrer ni à décoller. Vous aimeriez savoir pourquoi, après un an sans utilisation, malgré le changement des piles et le chargement de la batterie, votre drone refuse de se calibrer et de décoller, alors que vous suivez la procédure habituelle. Assurez-vous d'avoir changé les piles et chargé la batterie. Si le drone DJI MATRICE 100 ne se calibre pas correctement et ne décolle pas malgré vos actions habituelles, suivez les instructions de la notice pour effectuer le calibrage correctement. Vous ignorez pourquoi votre drone, qui fonctionnait très bien il y a un an, refuse maintenant de se calibrer et de décoller. Vous ignorez pourquoi votre drone, qui fonctionnait parfaitement il y a un an, ne parvient plus à se calibrer et à décoller malgré vos tentatives. La solution se trouve dans la notice si cela fait 1 an que vous n'avez pas utilisé votre drone DJI MATRICE 100 qui marchait très bien. Vous avez changé les piles et chargé la batterie, mais il ne veut pas se calibrer ni décoller alors que vous faites comme d'habitude.
Extrait du mode d'emploi DJI MATRICE 100
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
There are three types of fasteners that come with the Matrice 100. The curved fasteners and the 3° fasteners are preinstalled on the arm slots. Curved Fastener 0° Fastener 3° Fastener 6 © 2016 DJI. All Rights Reserved. DJI MATRICE 100 User Manual Curved Fastener: Fix on the inner arm slot. 0° Fastener: Fix on the outer arm slot so that the propeller rotation plane is perfectly horizontal. 3° Fastener: Fix on the outer arm slot so that the propeller rotation plane is at a 3° incline. It is recommended to use the 3° fasteners for a better flight experience. Clamp Ring Inner Arm Slot Outer Arm Slot 1) Loosen the four M2. 5x5 screws on the curved fastener and the 3° fastener on each of the frame arms. 2) Insert each frame arm into the outer and inner arm slots successively until the clamp ring reaches the outer arm slot. 3) Rotate the frame arm so that the fin on the clamp ring fits perfectly into the slot of the 3° fastener. Then tighten the four screws to fix the curved fastener and the 3° fastener in place. Ensure the arrow on the 3° fastener is pointing upwards. If you choose to use the 0° fasteners, remove the 3° fasteners from the arm slots first. Ensure that all propeller rotation planes are perfectly horizontal after mounting the 0° fasteners. Do NOT mix up the 0° fasteners and the 3° fasteners. Ensure that the four fasteners on the outer arm slots are the same. The 3° Fastener (with marking) The 0° Fastener © 2016 DJI. All Rights Reserved. 7 DJI MATRICE 100 User Manual 3. Connect the three motor cables of each motor (M1 - M4) to the ports of its corresponding ESC. Be sure to match the color of the cables and ports. Connect the LED cable of each frame arm to the port of its corresponding ESC. LED Cable M1 - M4 Mark LED Port Color Mark Motor Cable 5. Pull the antenna cable of each frame arm through the cable tie on the lower plate of the center frame, and then connect each cable to its corresponding antenna port on the bottom of the flight controller (You may require some tools for this step). Note the arrangement of the antenna ports shown below. Antenna Cable Antenna Port Cable Tie M2 M4 M3 M1 Antenna ports on the bottom of the flight controller 6. Ensure the motor cables, LED cable, and antenna cable of each frame arm are correctly installed to their corresponding ports. [...] All Rights Reserved. Product Profile The DJI Matrice 100 is a stable, flexible, and powerful flying platform. Its open platform and highly customizable design makes it suitable for a wide range of applications in the areas of research, business, and recreation. The Matrice 100’s expandable center frame makes it easy to mount additional components and devices to achieve greater functionality and results. An extra battery compartment for a second Intelligent Flight Battery can be installed to deliver an extended flight time of up to 40 minutes. Developers are granted full control over their flying platform with the built-in API Control feature, giving them the freedom to customize a comprehensive aerial solution by using the DJI SDK. Installation Checking the Frame Arms 1. Ensure the motors are firmly attached to the frame arms, and can rotate freely. Ensure the landing gear is firmly attached to the frame arms, and the antenna covers are in good condition. Ensure that all cables are intact. Identify the marks M1, M2, M3, and M4 on the four frame arms. Motor M1 - M4 Mark Antenna Cover Landing Gear LED Cable M Motor Cables Antenna Cable Checking the Center Frame To check the center frame and connect the cables, first remove the upper plate and the battery compartment. Remove the two screws (M3x8 self-tapping) on the Aircraft Status Indicator. Then gently remove the indicator to avoid damaging the cables. Handle the indicator cable gently Aircraft Status Indicator © 2016 DJI. All Rights Reserved. 5 DJI MATRICE 100 User Manual 2. Remove the eight screws (M2. 5x8) on the mounting rails on the upper plate of the center frame. Then remove the mounting rails and the upper plate. Remove the four screws (M2. 5x5) on the battery compartment. Then remove the battery compartment. Now you may check the center frame. Check that components such as the flight controller and ESCs are intact, and that the cables are connected to ports with matching color labels. Cooling Fan Flight Controller ESC Aircraft Status Indicator Antenna Port Mounting the Frame Arms 1. Identify the M1 - M4 marks on the frame arms and the arm slots of the center frame. Mount each frame arm onto the corresponding position on the center frame. [...]..
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre drone DJI MATRICE 100 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Mardi 1 Janvier 2020.
