Notice CALIBER RCD 212BTI

Notice

---

CALIBER RCD 212BTI

© copyright CALIBER

Télécharger la notice

Extrait du mode d'emploi CALIBER RCD 212BTI

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

If noise is still experienced when the motor of the vehicle accelerates, a choke should be placed in line with the power to the unit. The installation company will know what is required. When replacing the fuse(s) the replacement must be of the same amperage as shown on the fuse holder. Never replace a fuse with another of a different value. If the fuse blows again please contact your installation company. Do not block vents or heater panels. Blocking them will cause heat to build up inside and may result in fire. Double check that all wiring and connections are correct before reconnecting the battery and turning on the unit. After completing the installation and before operating the unit, reconnect the battery, Then press the (RES) button with a pointed object, such as a ball-point pen to set the unit to its initial status. After pushing the button, wait a few seconds for the red light to flash. • • • • • Tools for Installation •  removal wrenches are supplied for taking out the old unit and place with this brand name car radio. The following tools and supplies may also be needed for the installation: Tools for Installation: - Philips Screw-drivers - Wire Stripper - Wire Cutter - Hammer - Pencil - Electrical Tape - Electric Drill 6 Owner’ Manual Supplies for Installation: - Machine Screws - Crimp Connectors - 14 Gauge Wire for Power Connections - 14-16 Gauge Speaker Wires * The above are not supplied. RCD 212BTi • MANUAL Before You Install Automotive audio equipment installations can be troublesome at times, even to the most experienced of installation technicians. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. IMPORTANT: Remove the two transport screws from the top of the unit before installing. Remove the Old Unit from the Dashboard 1. Remove the outer trim frame. Insert the keys supplied with the old unit into both sides of the unit as shown in figure below until they click. Pull to remove the old unit from the dashboard. DIN Front Mount DO NOT DISCONNECT WIRES AT THIS TIME! 2. [...] • Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. To avoid short-circuiting, cover all disconnected lead with insulating tape. There is a possibility of shortcircuiting if the leads are not insulated. • Route and secure all wiring so it cannot touch any moving parts, such as the gear lever and handbrake. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle’s body. • Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead’s insulation and cause a very dangerous short. • Do not shorten any leads. If you do, the protection circuit may fail to work when it should. • Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. • Since a unique audio I/C circuit is employed, never wire so the speaker leads are directly grounded or the left and right – speaker leads are common. • When this product’s source is switched ON, a control signal is outputted through the orange lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. 300mA 1 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal. • When an external power amp is being used with this system, do not connect the orange lead to the amp’s power terminal. Likewise, do not connect the orange lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and a major malfunction. Refer to the relevant owner’s manual Owner’ Manual 5 RCD 212BTi • MANUAL Warnings Before Installation • • for details on connecting the power amp and other units, then make the connections correctly. Do not block any vents or heater panels. Blocking them will cause heat to build up and may result in fire. Make sure that the unit has a good chassis ground. A good ground connection will eliminate most electrical noise. A good chassis ground requires a tight connection to the vehicles metal chassis. [...]..

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre autoradio CALIBER RCD 212BTI : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Mercredi 10 Octobre 2017.