Notice plaque de cuisson BRANDT TE40B et pièces détachées
Le mode d'emploi plaque de cuisson BRANDT TE40B vous rend service
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre plaque de cuisson BRANDT TE40B : mode d'emploi, notice d'utilisation, manuel d'instruction.
Si vous n'êtes pas certain de votre références, vous pouvez retrouvez toutes les autres notices pour la catégorie Plaque de cuisson Brandt.
Cliquez sur le bouton orange pour lancer le téléchargement du mode d'emploi BRANDT TE40B. La notice BRANDT est en Français.
Le téléchargement peut durer plus d'une minute, la notice fait 1403 Ko.
Extrait du mode d'emploi : notice BRANDT TE40B
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
WHAT SHOULD YOU DO:
The appliance is not receiving Inspect the electrical cirelectricity. The electrical sup- cuit breaker and fuses. ply is defective or the hook-up is incorrect. The electronic board is functioning poorly. The hob is locked. Call the After-Sales Service Department. See chapter on using the child safety system. ·During operation
YOU OBSERVE THAT:
The hob stops working and it emits a beep approximately every 10 seconds and a or "F7" is displayed. A series of small displayed. or "F7" is
There was an overflow or an object is in contact with the control panel. The electronic boards heated up. WHAT SHOULD YOU DO:
Clean the hob or remove the object, then begin cooking again. See "Built-In" section. See section on cookware for induction. After turning on a heating zone, The cookware used is not suitable for induction or is less the indicator lights on the control panel continue to flash. than 12 cm in diameter (10 cm for the 16-cm cooking zone). The saucepans make noise during cooking. Your hob makes a clicking sound during cooking. The fan continues to function a few minutes after your hob is turned off. This is normal with some types Nothing. There is no risk, of cookware. This is caused by neither to your hob nor to the transfer of energy from the your cookware. hob to the cookware. Cooling of the electronic components. Working normally. Nothing. Warning
In the event that there is a break, crack or opening--even minor--in the vitroceramic glass, immediately disconnect your appliance to avoid the risk of electric shock. Contact the After-Sales Service Department. 13
99641031_a_ml. [...] Your appliance can be easily integrated above a cabinet, an oven or a build-in-ready household appliance. You must simply ensure that the air intakes and air outlets are clear (See "Description of Your Appliance" section). · BUILD-IN
Follow the diagram above. Glue the foam seal underneath your appliance by following the outline of the worktop upon which your appliance will rest. This will allow you to achieve an airtight seal with the worktop. m
If your oven is located below your hob, the hob's thermal safety measures forbid the simultaneous use of the hob and the pyrolysis program of your oven. Your hob is equipped with an anti-overheating safety device. This safety can be activated, for example, when the hob is installed over an oven that is not sufficiently insulated. If this occurs, a series of small lines appear in the control panel. In this case, we recommend that you increase the ventilation of your hob by creating an opening in the side of your cabinet (8 cm x 5 cm) and/or that you install the oven insulation kit (reference 75X1652) that is available from the Post-Sales Service Department. Warning
You must ensure that the air intakes located under your cooking appliance remain clear at all times. For all types of installation, your induction hob needs proper ventilation. 5
1 / INSTALLING YOUR APPLIANCE
These hobs must be connected to the power grid via an electrical outlet that complies with EIC publication 60083 or an all-pole cut-off device that complies with installation regulations in effect. When power is first supplied to your hob, or after an extended power outage, an indicator light will appear on the control panel. It automatically disappears after approximately 30 seconds, or as soon as any touch control on the control panel is pressed. This display is normal and, if needed, serves as an indication to the after-sales service staff...
Vos avis sur le BRANDT TE40B
Tres bonne machine vient de ns lacher apres 17 an de bon et loyaux service.