Mes Notices

600 000 notices et 900 000 pièces détachées électroménager

Notice BRANDT DX951CF

Télécharger la notice

Extrait du mode d'emploi BRANDT DX951CF

Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.

Fonctionnement en recyclage: fig. 5 et 9 - Il est possible de retirer les clapets anti-retours. - Fixez contre le mur, en appui sur le plafond, le déflecteur plastique des fumées. Prendre soin de centrer le déflecteur par rapport au trait vertical tracé sur le mur (fig. - Préparez votre cheminée en prenant soin de placer les ouïes vers le haut de manière qu'elles soient visibles (fig. - Fixez la partie supérieure sur le déflecteur plastique. - Ajustez la longueur de la cheminée télescopique en descendant la partie inférieure et l'emboîter dans le sommet de la hotte. Comment changer la lampe ? Avant toute intervention, la hotte doit être mise hors tension, soit en retirant la prise, soit en actionnant le disjoncteur, 1. Retirez les filtres métalliques (fig. Dévissez puis changez l'ampoule E14-40W (fig. Replacez les filtres métalliques. 99635121_ML_A. qxd 14/12/04 16:52 Page 14 Comment nettoyer votre hotte ? La hotte doit être mise hors tension, soit en retirant la prise, soit en actionnant le disjoncteur, avant que les filtres métalliques soient enlevés. Après le nettoyage, les filtres métalliques doivent être de nouveau fixés conformément aux instructions. FILTRE CASSETTE Avant la première utilisation du filtre cassette, retirez le film de protection. IMPERATIF TOUS LES MOIS FILTRE CHARBON ACTIF Pour les hottes installées en recyclage IMPERATIF TOUS LES ANS ENTRETIEN Pour éviter tout risque d'incendie. Ce filtre retient les vapeurs grasses et les poussières. Il est l'élément assurant une part importante de l'efficacité de votre hotte. Avec un nettoyant ménager du commerce, puis rinCe filtre retient les odeurs et doit être changé au moins tous les ans en fonction de votre utilisation. [...] If the instructions for the hob installed under the hood specify a distance of more than 70 cm, this requirement must be respected. - Draw a horizontal line 70 cm minimum from the cooktop. - Draw a vertical line on the wall running from the ceiling to the lower edge of the hood. - Place the mounting hole template against the wall (fig. - Drill the 6 holes. Insert the 6 wall plugs. - Screw up the top two screws of the hood, but not completely - allow them to protrude by 5 mm. - Remove the metal filter. - Attach the suction hood to the two screws (fig. - Screw up the two screws at the bottom. Adjust the level of your hood before fully tightening up all four screws. Connecting up your hood This appliance is delivered with a H 05 VVF power cable with 2 conductors of 0. 75 mm2 (neutral, live). This must be connected to the 220-240 V single phase mains network via a CEI 60083 standard plug which must remain accessible following installation. We will not be liable in the event of an accident arising following incorrect installation. The fuse for your installation must be 10 or 16A. If the power cable is damaged, call the after sales service department in order to avoid danger. 99635121_ML_A. qxd 14/12/04 16:52 Page 6 Assembling the chimney Hood to be used with external evacuation : fig. 4 and 8 - Attach the metal chimney bracket to the wall, also placing this against the ceiling (fig. Take care in aligning the 2 triangular slots on the metal bracket with the vertical line on the wall. - In the case of a flue with a diameter of 125 mm, use the adapter supplied (fig. If your exterior duct is below 125 mm, you must obligatorily connect your hood in recycling mode - Prepare your telescopic chimney taking care to block off the vents (fig. Fit the chimneys into one another as far as they will go. - Fit the upper part to the metal bracket...

Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre BRANDT DX951CF : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Mercredi 6 Juin 2012.

Liens commerciaux