Pièces détachées BRANDT CCR200SI
* Prix indicatif de vente, le prix exact sera affiché après que vous ayez saisi la référence de votre appareil.
Extrait du mode d'emploi BRANDT CCR200SI
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
- Fit a wooden panel to the door (a chipboard panel OK if on a temporary basis) and adjust the springs. - Contact the installer. - Leak at the tap Small leak around or under the machine (move the machine to locate the - Leak in the machine leak better) The door "catches" when - The machine or the door is not correctly you close it centred on the tub - The door springs are The door falls down not tensioned enough heavily when you open it to compensate for the (integratable models) weight of the basket. The door is not level when open or goes back up too quickly (integratable machine) - The door springs are over-tensioned. - No wooden panel Washing economically regenerating salt or rinse aid. Follow the recommendations in and ecologically Do not wash the items first by hand (unnecessary waste of water). Use your dishwasher's capacity to the full. You will then wash economically and ecologically. Always select a washing programme suitable for the type of items and how dirty they are. Do not overdose with detergent, these instructions (Pages 6 -7-8) and the manufacturer's instructions on the pack. Ensure that the water softener is set correctly (see Page 6) The upper basket will not - Poor handling (the bas- - Move the basket graduket has been pulled ally on one side and stay in the high position upwards too quickly). then the other (until you hear a "Click") = -> see the Operating Instructions. Programming, display anomalies Possible causes What to do - Use these programmes The cycle takes too long. - The energy-saving programmes take longer preferably at night because they compensate when the length and for the lower washing and the finishing time are drying temperatures by not important. longer agitation and drying. 19 18 Troubleshooting, what to do? Programming, display anomalies The lights light up one after another Possible causes - Wrongly programmed. [...] You must set the water softener according to the hardness of the water in your area. What to do before using the machine for the first time Filling the regenerating salt reservoir You must fill this, with water just before starting your first wash then add the salt: Salt reservoir - Measuring the water hardness To do this: contact your local water supplier to find out the water hardness level and adjust on the machine as described below. - Filling with salt is essential to obtain a good wash with no streaks. The salt regenerates the resins, which soften the water by removing its limestone content unless Never put deterthe water is already sufficiently soft gent in this reservoir: (see "Adjusting the water softener"). water this will ruin the softener. - Unscrew the salt reservoir's stopper and remove it. - Fill the reservoir with regenerating salt specially designed for dishwashers. (the funnel available from the after-sales department reference : 31X3964) - On the first time, add water until it reaches the edge of the reservoir. - Screw the salt reservoir's LT stop back in fully. SA Do not use kitchen salt. Should any regenerating salt overflow when filling, we recommend that you remove the loose salt crystals to avoid oxidising the tub. Indication of the level of instance when putting the regenerating salt machine into operating using the SALT indicator light: sample. This illuminates showing salt If the water is especially needs to be added. After you have soft and does not require refilled the salt reservoir, the light the use of any regenerating may still remain lit until the salt has dissolved sufficiently, generally salt, the SALT light remains lit. after one cycle (or if the reservoir has not been completely filled, for 7 Adjustment via the cursor inside the tub. Adjust the setting using the cursor on the left-hand side inside the tub by positioning it correctly on the desired number, depending on the water hardness...
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre congélateur BRANDT CCR200SI : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Mercredi 1 Janvier 2008. Si vous n'êtes pas certain de votre références, vous pouvez retrouvez toutes les autres notices pour la catégorie Congélateur Brandt.
Envoyer vos modes d'emploi - Foire aux questions - Dernières recherches - Derniers ajouts - Sitemap - Contactez-nous - Conditions générales - Politique de cookies
Copyright - Tous droits réservés.
Les noms de marques cités appartiennent à leurs propriétaires respectifs.