Mes Notices
* Prix indicatif de vente, le prix exact sera affiché après que vous ayez saisi la référence de votre appareil.
Vous avez retrouvé une pièce plastique blanche, qui pourrait être le support d'un charbon, dans le tambour de votre lave linge, pour l'instant ce dernier semble continuer à fonctionner correctement. Le manuel de votre BOMANN WA 5720 vous sera utile pour trouver la position d'origine de l'élément que vous venez de retrouver. Deux voyants clignotent sur le cadran de votre machine, il s'agit des positions 600 et 1000 de la vitesse de rotation du tambour, une pièce détachée d'électroménager pour lave-linge importante. Vous avez d'ailleurs constaté qu'il n'y avait plus d'essorage en fin de cycle. Le tableau digital de votre lave linge ne s'allume plus, pourtant l'électricité n'est pas coupée chez vous. Vous trouverez le moyen de rallumer le tableau de contrôle de votre machine à laver grâce à la notice de votre BOMANN WA 5720.
Les instructions détaillées pour l'utilisation figurent dans le Guide de l'utilisateur.
CAUTION: CAUTION: • • Looseness locknuts can cause vibration and noise. The feet must never be removed. Do not restrict the floor clearance through ca carpets, strips of wood or similar. Danger of heat accumulation! Water connection CAUTION: • • • The Installation of the water supply must conform to the local laws and regulations. The appliance is not suitable for hot water supply. Use the new supplied hose set to connect the appliance to the water supply. Do not reuse old or used connection sets. 8 CAUTION: • If the water pipe is new or long time not used, ensure before connecting to the water system, that the water is clear and free from contamination. Notes on inlet hose safety system (delivery scope depending on model) (delivery model) The safety system consists of a double-walled inlet hose. It guarantees to cut off the water supply when leakage of the inner hose. Switching off the water supply leads over an electronic contact. If necessary, you can order an inlet hose safety system from your dealer or in our online accessories shop, www. bomann. To order, use the reference number found under www. bomann. “Technical Data”. Connect the water inlet hose (cold water connection) NOTE: NOTE: The water pressure must be between 0. 05 MPa and 1 MPa. With higher pressure: use a pressure regulator. • Connect the water inlet hose to a water thread with ¾“. Screw the hose firmly in the direction of the screw thread; pay attention for a tight fit. • Connect the other end of the inlet hose to the inlet valve on the appliance back; pay attention for a tight fit too. Connect the water drain hose NOTE: NOTE: The drain hose has a length of approx. 5 m and can extend with a suitable hose and connecting piece to a length of max. CAUTION: In order to prevent backflow of contaminated water, the free end of the hose must not come under the water level of the drain. • Connect the drain hose to a drain pipe with a minimum diameter of 40 mm; altern alternatively the drain hose can be fixed to a sink or directly to the drainage. 9 • Always make sure that the hose is not bent or se squeezed. Use e. a hose holding bow (a) (not supplied). The hose must be installed at a height of min. 600 mm and max. 1000 mm above the floor. 00 Secure the hose securely in order to avoid a • • change in position and with it a water leakage. [...] Otherwise there is dandanhazard! ger to life or electric shock hazard CAUTION: For a correct operation the appliance must be connected properly. The specifications for water supply and drain as well as the electrical connection must fulfill the required criteria. Remove the transport locking screws CAUTION: • Before using, all transport locking screws must be removed from the appliance back. Otherwise it may cause serious damages. • Keep the transport locking screws for later use / transport. Never transport the appliance without properly attached transportation safety! • Loosen the screws from the appliance back with a wrench and remove them. • Plug the holes of transport locking screws with the supplied covers. Installation location • The site should be located near the water inlet and outlet, as well as near a properly grounded power socket. • Good ventilation around the appliance is required, in order to dissipate the heat properly. Sufficient clearance must be created for this purpose. • The clearance to the front must be created so, that the appliance door can open without being impeded. • Make sure that the floor on which the appliance is installed, is even, heat-resistant and clean. 7 • Take care of a solid and horizontal position of the appliance. If the appliance is not horizontally leveled, adjust the feet accordingly (see “Adjust the feet”). Power cord and water hoses may not kinked or squashed. The wall socket must be freely accessible. the Avoid the installation: near heaters, next to a stove, direct sunlight or any other heat sources; at locations with high humidity (e. outdoors), as metal parts would be su susceptible to corrosion under such circumstances; in rooms where the temperature could drop below freezing. Do not expose the appliance any weather. near volatile or flammable materials (e. gas, fuel, alcohol, paint, etc. • • • Adjust the feet Loosen the locknuts with a wrench. Turn to the right to let down the unit; turn to the left to lift up the unit. Tighten the lock nuts with the wrench when the appliance is properly leveled. The feet must have solid ground contact. Check with a spirit level if the appliance is leveled horizontally. [...]..
Téléchargez votre notice ! Téléchargement gratuit et sans inscription de tous types de documents pour mieux utiliser votre lave-linge BOMANN WA 5719 : mode d'emploi, notice d'utilisation, manuel d'instruction. Cette notice a été ajoutée le Samedi 8 Aout 2019.
Envoyer vos modes d'emploi - Foire aux questions - Dernières recherches - Derniers ajouts - Sitemap - Contactez-nous - Conditions générales - Politique de cookies
Copyright - Tous droits réservés.
Les noms de marques cités appartiennent à leurs propriétaires respectifs.